Updated November 2026
Why has my electric window stopped working? The four usual causes are a blown fuse, a faulty window switch, a failed window motor or a broken window regulator. If you can hear the motor hum but the window doesn’t move, the regulator is the likely culprit. If nothing happens at all, check the fuse and switch first.
What Is a Window Regulator?
Window regulators are the mechanisms inside your car door that allow you to easily open and close your windows. Most modern cars have electric windows which are operated using a switch. The window regulators and motors that power them can become worn or damaged over time. Window regulator repair is sometimes possible and in this article, we go through some common problems and solutions. A more straightforward solution is often replacing a window regulator outright but is not always necessary.
Factors such as window stickers or car window tinting which essentially increases the thickness of the window can cause extra resistance and put stress on the window mechanism, as can operating the windows in frosty conditions when they are frozen shut. Certain makes and models of car are known for having electric window issues such as the Renault Megane which has a prolific electric window fault.
If you have issues with your electric windows our guide to common electric window problems & solutions will help you figure out what exactly needs to be fixed or replaced.
Electric Window Problems: Symptoms and Likely Causes
| What you notice | Likely cause | What to check |
|---|---|---|
| All windows stopped working | Blown fuse | Check the window fuse in the fuse box |
| One window dead, no sound at all | Switch, wiring or motor | Try the driver’s master switch, then check wiring and power to the motor |
| Motor hums but the glass doesn’t move | Window regulator | Remove the door panel and inspect the regulator cables and clips |
| Window drops or tilts to one side | Window regulator | Check for a snapped cable or broken guide clip |
| Works from the driver’s master switch but not its own switch | That window’s switch | Clean or replace the switch |
| Window moves slowly or sounds noisy | Worn regulator, tired motor or dry seals | Treat the seals; inspect the regulator and motor |
| Only the passenger windows won’t work | Window lock button | Check the lock button hasn’t been pressed |
Can a Faulty Electric Window Fail the MOT or NCT?
Driver Side Windows are checked during the MOT or NCT (National Car Test). They can result in a test failure for the following reasons:
- Insecure.
- Window opening mechanism of driver’s window not operating.
Signs of a Faulty Window Regulator
- Window does not go up or down when buttons are pressed.
- Operating the window makes an unusual or loud sound.
- Window drops to one side.
- Window closes very slowly or fails to close completely
Did You Know?
When testing the windows, use both the driver’s side master control switch and the switch at the malfunctioning window. If one of these switches operates the window as normal, then you know that there is a problem with one of the switches. 
Almost all cars with electric windows have a lock button that cuts power to all windows apart from the driver’s side for safety reasons. If your windows aren’t working, it’s worth checking if this button has been pressed accidentally!
The 4 Main Reasons an Electric Window Stops Working
- Blown fuse
- Faulty window switch
- Faulty window motor
- Faulty window regulator
How to Diagnose an Electric Window Fault, Step by Step
Step 1: Check the Fuse
Testing a Fuse with a Voltmeter: The safest method for testing a fuse is to use a voltmeter (or a multimeter that is set to volts). Turn your ignition to the on position and clamp the negative (black) lead to a ground. Locate the two exposed square pieces of metal that are on top of the fuse in question, using the positive (red) lead touch the first metal square, then do the same to the other, as shown in the image to the left.
The voltage reading should be between 12-14 volts. Correct readings on both sides of the fuse indicate that the fuse is not blown and is working. If only one side of the fuse is giving a reading then the fuse is blown. If neither side gives a reading, current is not flowing into either side of the fuse and there is an electrical problem upward of that area on the circuit.
How to Visually Check a Fuse
Use a fuse puller to extract the fuse from the socket. (Some vehicles will have this tool inside the fuse box.) Pull on the fuse gently to remove it, you may need to wriggle it slightly but be careful not to damage it or the socket. If you don’t have a fuse puller, you can use long-nose pliers instead. When the fuse has been removed, check the metal strip inside for any breaks or fractures.
If the metal strip is broken as shown in the image below, then the fuse is blown and needs to be replaced. It’s critically important to replace it with a fuse of the exact same amperage rating. This rating is the number that is written on top of the fuse or stated in the fuse box cover. Using a fuse of lower or greater amperage could result in a fire or damage other components on the car.
Tip: Check for loose connections or wires around the fuse box. Tighten them and check to see if the windows work. A little electrical contact spray can also help.
Step 2: Check the Window Switch and Wiring
Tip: Check the window switches for any dirt or loose/worn cables that could be causing the window to malfunction. If the fuses are not blown then a deeper investigation is needed.
Step 3: Remove the Door Panel and Inspect
The door panel will need to be removed. It’s important to follow manufacturers procedures for removing this panel to avoid any damage. The next step is to remove the moisture barrier liner by slowly peeling it off and placing it in a safe place. Once this is done, visually inspect the plastic guides, connections, wiring and components for any sign of damage or if any of them are not secure. 
Step 4: Check Power to the Window Motor

Using a digital volt meter, test the connection that is going to the motor for current. Motors with two wires are analogue systems and are safe to test.
However, motors with more than two wires are called digital systems and a professional diagnosis is recommended. Use the back probing method to test if power is flowing through the connector leading to the motor when the window switch is pressed (remember to reconnect the window switch when testing). Back probe testing involves inserting the probes (leads) into the motor side of the connector as shown in the image below.
Tip: Avoid piercing any wires or front probing the connector as this could lead to further problems.
When checking the wires you are looking for a reading of either -12 volts or 12 volts. If the reading shows full current and the motor is not running it means that the motor is at fault.

A lower reading means that sufficient current is not reaching the motor and that the problem is further up the circuit. Using the drop testing voltage method you can test for any differences in volts at either side of the connector i.e. if voltage reads 10 volts at the motor side of the connector and the overall voltage is 12 volts there is resistance in the circuit that could cause the motor to run abnormally.
Tip: It’s recommended to change the motor and window regulator at the same time. If one of them was to break again, you will be back to the same situation.
Tips to Extend the Life of Window Regulators & Motors
- As soon as the window is fully up or down release the button, keeping it pressed can put tremendous strain on the motor and the regulator components.
- Using rubber care products such as Nextzett Gummi Pflege or silicone spray can keep rubber seals from getting hard and drying out. This will allow the window to go up and down freely.
If you’ve been through all the tests and checks above and need to replace your window regulator or motor, you’ll find them on our website here. You can also check out our window regulator Youtube playlist to see if we have a ‘How To’ video for your car
Window Regulator Fitting Videos
Here’s an example of one of the most popular window regulator fitting videos. This video is for a Ford Fiesta:
Driving a BMW 3 Series from 1998–2005? See our step-by-step guide to window regulator replacement on the BMW 3 Series.
Electric Window FAQs
Can I drive with a broken window regulator?
You can, but it’s not ideal: a window that won’t close leaves your car open to rain and theft, and a window that slips down can fall open while you drive. A driver’s window that won’t operate can also fail the MOT or NCT, so get it fixed soon.
How do I know if it’s the motor or the regulator?
Listen when you press the switch. If the motor hums or clicks but the glass doesn’t move, the regulator is usually broken. If there’s no sound at all, check the fuse and switch, then test for power at the motor connector – full power with no movement means the motor has failed.
Can I replace a window regulator myself?
Yes, it’s a common DIY job if you’re comfortable removing a door panel. Follow the manufacturer’s procedure for the panel, and check our window regulator YouTube playlist for a video for your car. Many people replace the motor and regulator together.
Why does my window go back down after closing?
This is usually the anti-pinch (auto-reverse) safety system, which can lose its settings after a battery change or a repair. On many cars you can reset it by holding the switch up for a few seconds once the window is fully closed – check your handbook for your model.
We hope this has helped answer some of your questions – thanks for reading!













Leave a Reply